De gr37 versie is bedoelt voor gnuradio 3.7, de andere voor gnuradio 3.6 en zijn niet uitwisselbaar.
Heb je een installatie met 3.7 gebouwd? Zo ja, frequenties zoeken en luisteren.
Zodra je een frequentie te pakken hebt kun je met de "t" functie binnen Telive alle naastgelegen kanalen bekijken. Zo vind je snel de overige kanalen van een systeem. Verander je van kanaal dan kan je met "z" het kanalen lijstje van het vorige kanaal wissen en weer opnieuw opnieuw op laten bouwen.
Succes.
Elmar
Hier werd ik dus ook op het verkeerde been gezet.
Ik had precies dezelfde schermen.
Daarna had ik nog wel een foutmelding..
Kernel driver is active, or device is claimed by second instance of librtlsdr.
In the first case, pleas either detach or blacklist the ernel module (dvb_sub_rtl28xxu), or enable automatic detaching at compile time.
Trying to fill up 1 missing channel(s) with null source(s)
This is being done to prevent the application from crashing due to gnuradio bug #528
Na veel google....
Ik heb een bestand gemaakt:"ban-rtl.conf"
En zet de volgende tekst in dat bestand:
blacklist dvb_sub_rtl28xxu
zet het bestand "[/font]
ban-rtl.conf[/font]
"[/font]
in de map: /etc/modprobe.d/ [/font]
[/font]
(eerst had ik geen schrijfrechten. Nadat ik in een terminalvenster "
sudo nautilus /etc/modprobe.d/" zonder aanhalingstekens had getypt, kon ik daar het bestand neerzetten.
Nu wordt de RTL stick (R820T2) na een restart wél gezien.
Het ziet er naar uit dat het werkt.
Nu nog kijken hoe ik precies de frequentie kan wijzigen. (vorige berichten gelezen en geprobeerd, maar nog geen resultaat)
Maar dankzij de vorige berichten ben ik nu wel verder gekomen, dat is eigenlijk ook de reden van dit bericht om elkaar te helpen.
Ik werk met een HP probook 6550b, Intel Core i5 CPU M450 @ 2,40GHz x 4 met 4GB intern geheugen en een 250GB SSD HD.
Die SSD is wel aan te raden zeg.. lekker rap!!
Is het trouwens de bedoeling dat als je telive wil opstarten het hele feest opnieuw moet intikken??
Of is er een scrip o.i.d. voor?
Running the SoftwareOpen a terminal window and browse to ~/osmo-tetra-sq5bpf/src and run ./receiver1 1.cd ~/osmo-tetra-sq5bpf/src ./receiver1 1[/li]
[li]
Open a second terminal window or tab and open a specially sized xterm window using the following./usr/bin/xterm -font fixed -bg black -fg white -geometry 203x60[/li]
[li]
In the xterm window, browse to ~/telive and run ./rxx.cd ~/telive ./rxx[/li]
[li]
Open another terminal window or tab and browse to /tetra/bin and run ./tetrad.cd /tetra/bin ./tetrad[/li]
[li]
Open another terminal window or tab and open GNU Radio Companion by typing the following.gnuradio-companion[/li]
[li]
In GNU Radio open the telive_1ch.grc file which is found in ~/telive/gnuradio-companion.[/li]
[li]
On the left of the GNU Radio flowgraph, double click on the variable labeled Center Freq and change the frequency to the frequency of your TETRA signal that you found earlier subtracted by 500 kHz. E.G. If your TETRA signal was found at 858.562 MHz, you’d type your center frequency as 858.062 MHz. This is because the default offset value is set to 500 kHz.[/li]
[li]
Double click the variable labelled ppm and input your dongles particular PPM correction value.[/li]
[li]
Execute the flowgraph by clicking on the cog icon on GNU Radio Companion toolbar.[/li]
[li]